Articulated Laptop Pivot Mount for Harley Davidson Motors

Adapting laptop computers and printers to motorcycles has been a challenge for years. Space on a police motor is always at a premium, yet all agencies want to utilize as much common equipment as possible, including laptops. Additionally, agencies are faced with the logistical issues of using the laptop, while wanting to keep an eye on the violator and not standing with your back to approaching traffic. FMS Accessories has developed a pivot mounting that allows the laptop to be opened and rotate around the radio box, enabling better positioning of the officer relative to the violator and traffic. Select the laptop mount type as well as the base plate mount type. Low profile printer housing shown in several photos is optional. Select roll paper spindle diameter based on your agency paper supplier. Brother PocketJet Printer not included.

Special relay harness designed to disable power to your LIND laptop charger when the motorcycle ignition is OFF. Enables charging the laptop battery when motorcycle is running, but shuts-off 50 seconds after ignition OFF via SPST relay. Due to varied locations for LIND chargers, unit comes with long wire leads and an adhesive cable tie base to mount relay where most convenient. Note that without this relay harness, each and every time the motor is turned-OFF, the LIND charger will remain ON for 30 minutes, draining the auxiliary battery. Reducing parasitic load extends the life of the auxiliary battery! R 1300 RT-P has a new circuit replacing this harness - order FMSA-EL-LCP.

Brother PocketJet printer power cable, for use with BMW 2.5 mm Code B connector to attach Brother Pocket Jet printer power cable to the power plug vacated by the terminal bracket / lighter socket when installing the pivoting laptop / low profile printer housing in BMW motors. Connect your Brother Pocket Jet printer power cable directly to the motorcycle without a power converter. Order Printer Power Plug separately. Note: if you have the tool you can remove the pin housing from the lighter socket and only need to purchase the 2.5 mm BMW pins. Free shipping is limited to the continental United States. Shipping charges apply to international shipments.

The FMS LVD Power Center provides a (Low Voltage Disconnect) connection bank for law enforcement / public service vehicles. The 50A Power Center provides separate managed power outlets for all standard authority functions for motorcycle / utility vehicle use. Each power output can be set to be powered either with ignition-ON, or continue to be powered for a specific time after ignition-OFF based on timer duration selected. The timer duration is adjustable in 15-minute increments up to 1.75 hours after ignition-OFF. One fused outlet is provided for direct battery connection (fused, no LVD or timed function), primarily for an external charging port. All other outlets are LVD managed, meaning that if the voltage in the battery(s) that the LVD Power Center is connected to drops below either 9V or 11V (selectable) for more than 30 seconds, the Power Center shuts down to protect the battery(s). Inputs are Bat +, Bat - and IGN. The IGN input is a voltage sensing input, so if no dedicated IGN input is available, you can connect items such as taillight or other accessories that are ON when the IGN is ON. Note that if a (starter) load-shedding power source is used, the non-timer selected outputs will be off when the starter is activated. All outputs have either a selectable ATM fuse (up to 15A) or are load managed circuit, with a variety of load choices. 3-15A outputs (emergency lighting, siren, mobile radio), 7 load managed outputs 1-7A, 2-5A, 2-3A, 2-2A (radar, Set-Com/PVP, PC charger, video, BT amp, etc.) plus the BAT direct connection (suggest 5A for battery charger / power outlet). The 10 outlets that can be time managed are selected via a 1-10 DIP switch. This feature enables you to select the proper output based on load rating, then decide with each output whether you want it time managed or not. Outputs 1-3 are higher-current and use a set-screw wire connection. Outputs 4-10 and BAT use the 2-conductor accessory connection plugs provided (FMSA-EL-ACP).